set RTC via progcom

AGENTS.md

@@ -94,6 +94,10 @@ The Python `MCU` client for ProgCom device `MC 0` follows
   minor 0;
 - `read_persistent_log_info()` and `read_persistent_log_entries()` read the
   frozen (offsets final, not yet firmware-served) persistent-log pages; and
+- `set_rtc(when=None)` writes the Control-page RTC set word (needs
+  `RTC_WRITE`, map minor >= 4): host local wall-clock time as seconds since
+  1970-01-01 of that clock, not Unix time. Client and firmware refuse values
+  before 2026-01-01. `mcu_set_rtc.py` is the command-line wrapper;
 - `send_control(McuControlCommand...)` writes the one-byte write-only
   Control-page command (`ASSERT`/`RELEASE_PROGCOM_POWER_INHIBIT`,
   `CLEAR_POWER_FAULT`, `CLEAR_ALARM_LATCHES`, `ZYNQMON_ENABLE_TRANSMIT`,

MCU_REGISTER_MAP.md

@@ -23,7 +23,7 @@ Read-only.
 | --- | ---: | --- |
 | `0x00` | 4 | ASCII magic `CMCU` |
 | `0x04` | 1 | map major version (`1`) |
-| `0x05` | 1 | map minor version (`3`) |
+| `0x05` | 1 | map minor version (`4`) |
 | `0x06` | 1 | hardware revision |
 | `0x07` | 1 | ADC channel count (`21`) |
 | `0x08` | 4 | capability bitmap |
@@ -62,6 +62,7 @@ Capability bits (bitmap at `0x08`):
 | 7 | `CONFIG` | yes (page `0x05` readable; map minor ≥ 2) |
 | 8 | `RUNTIME` | yes |
 | 9 | `CONFIG_WRITE` | yes (page `0x05` writable; map minor ≥ 3) |
+| 10 | `RTC_WRITE` | yes (page `0x7f` offset `0x04`; map minor ≥ 4) |
 
 A capability bit is set only once its page is fully implemented; a client
 must not assume a page works just because its offsets are frozen here.
@@ -311,7 +312,13 @@ count is published — scan all 64 and filter erased/empty sentinels.
 
 ## Page `0x7f` — Control — **implemented**
 
-Write-only. One command byte at offset `0x00`.
+Write-only. One command byte at offset `0x00`, and from map minor 4 the RTC
+set word at offset `0x04`.
+
+| Offset | Size | Field |
+| --- | ---: | --- |
+| `0x00` | 1 | command code, table below |
+| `0x04` | 4 | RTC set: local wall-clock seconds since 1970-01-01 00:00:00 (needs `RTC_WRITE`, bit 10) |
 
 | Code | Command |
 | ---: | --- |
@@ -348,6 +355,20 @@ timeout): a full queue is real backpressure and should surface to the
 remote client immediately as `MCU_REG_QUEUE_FULL`, not stall the ProgCom
 UART link waiting for space.
 
+**RTC set (`0x04`).** The RTC carries no time zone. The value is the setter's
+local wall-clock time expressed as seconds since 1970-01-01 00:00:00 of that
+clock, so it is *not* Unix time; `cm_interface` (`MCU.set_rtc`) computes it
+with `calendar.timegm` on the host's local time. A DST change shifts the RTC
+only when someone sets it again. Values below `1767225600` (2026-01-01
+00:00:00) return `invalid MCU value`. The write is synchronous, with no queue,
+and is what the Runtime page's RTC fields read back. On map minor 3 firmware
+the offset returns `invalid MCU address`; check bit 10 first.
+
+The RTC set is not serialised against the CLI `time set` command. Each loads
+the calendar with two register writes (time, then date), so two concurrent
+setters could leave one caller's time with the other's date. No lock is taken; do not set the clock from both
+interfaces at once.
+
 Each alarm-clear command targets exactly one alarm task's queue — there is
 no combined "clear all alarms" command, so no command ever needs atomic
 delivery across more than one queue.
@@ -361,7 +382,7 @@ delivery across more than one queue.
 | address not inside a declared field | `invalid MCU address` |
 | read/write crosses the end of a field, or length outside 1-4 | `invalid MCU read span` |
 | write to a field with a length other than its width (pages `0x05`, `0x7f`) | `invalid MCU write span` |
-| valid address and length, value outside the field's clamp (page `0x05`) | `invalid MCU value` |
+| valid address and length, value outside the field's clamp (page `0x05`, page `0x7f` RTC set) | `invalid MCU value` |
 | write to a read-only page | `MCU register is read only` |
 | read from a write-only page | `MCU register is write only` |
 | valid request, queue-owned op not yet accepted | `MCU queue full` |

README.md

@@ -133,6 +133,10 @@ rt = mcu.read_runtime()                # page 0x06, map minor >= 1 firmware
 print(rt.heap_free_bytes, rt.system_stack_untouched_words, rt.fpga_done)
 print(rt.rtc.isoformat())              # "unset" when the RTC is not valid
 
+# Needs map minor >= 4 (RTC_WRITE). Sets host local wall-clock time; the RTC
+# has no time zone. Refuses times before 2026-01-01. CLI: mcu_set_rtc.py
+mcu.set_rtc()
+
 mcu.send_control(McuControlCommand.CLEAR_ALARM_LATCHES)
 ```
 

device/mcu.py

@@ -5,6 +5,8 @@
 ``MCU_Reg.h`` — keep this module in sync with it, not the other way around.
 """
 
+import calendar
+import datetime
 import math
 import struct
 from enum import IntEnum, IntFlag
@@ -127,6 +129,22 @@ class ConfigReg(IntEnum):
 ALARM_VOLT_CPCT_MIN = 100     # 1 %
 ALARM_VOLT_CPCT_MAX = 1000    # 10 %
 
+# Lowest RTC set value the firmware accepts (``RTC_SET_MIN_SECONDS``):
+# 2026-01-01 00:00:00 local wall-clock time, in the units of rtc_local_seconds().
+RTC_SET_MIN_SECONDS = 1767225600
+
+
+def rtc_local_seconds(when: datetime.datetime) -> int:
+    """Wire value for the RTC set field: seconds since 1970-01-01 00:00:00 of
+    ``when``'s wall clock. Not Unix time: the RTC carries no time zone.
+
+    A naive datetime is taken as wall-clock time as given; an aware one is
+    first converted to the host's local zone. Sub-second precision is dropped.
+    """
+    if when.tzinfo is not None:
+        when = when.astimezone().replace(tzinfo=None)
+    return calendar.timegm(when.timetuple())
+
 
 class AlarmTempDevice(IntEnum):
     """Matches the firmware's ``enum device`` (``Tasks.h``): FF, DCDC, TM4C, FPGA."""
@@ -159,6 +177,7 @@ class RuntimeReg(IntEnum):
 
 class ControlReg(IntEnum):
     COMMAND = 0x00                # uint8, write-only
+    RTC_SET_LOCAL = 0x04          # uint32, write-only, see rtc_local_seconds()
 
 
 class McuControlCommand(IntEnum):
@@ -180,6 +199,7 @@ class McuCapability(IntFlag):
     CONFIG = 1 << 7
     RUNTIME = 1 << 8
     CONFIG_WRITE = 1 << 9
+    RTC_WRITE = 1 << 10
 
 
 class McuBuildType(IntEnum):
@@ -835,3 +855,30 @@ def send_control(self, command: McuControlCommand,
         page = McuPage.CONTROL
         self._require_page(page, check_capability)
         self.write_reg(self._reg(page, ControlReg.COMMAND), bytes([int(command)]))
+
+    def set_rtc(self, when: Optional[datetime.datetime] = None,
+                check_capability: bool = True) -> int:
+        """Set the MCU RTC to a local wall-clock time; returns the value sent.
+
+        ``when`` defaults to the host's local time now; see
+        :func:`rtc_local_seconds` for naive vs. aware datetimes. The RTC has
+        no time zone, so a DST change shifts it only when it is set again.
+        Values before 2026-01-01 raise ``ValueError`` and send nothing.
+
+        Not serialised against the CLI ``time set``: two concurrent setters
+        can leave one's time with the other's date.
+        """
+        if when is None:
+            when = datetime.datetime.now()
+        seconds = rtc_local_seconds(when)
+        if not RTC_SET_MIN_SECONDS <= seconds <= 0xFFFFFFFF:
+            raise ValueError(
+                "RTC time {} outside 2026-01-01..2106-02-07".format(when.isoformat()))
+        page = McuPage.CONTROL
+        self._require_page(page, check_capability)
+        if check_capability and not self.capabilities() & McuCapability.RTC_WRITE:
+            raise McuCapabilityUnavailable(
+                "firmware does not advertise {}".format(McuCapability.RTC_WRITE.name)
+            )
+        self.write_reg(self._reg(page, ControlReg.RTC_SET_LOCAL), struct.pack("<I", seconds))
+        return seconds

tests/test_mcu.py

@@ -1,4 +1,5 @@
 import contextlib
+import datetime
 import io
 import math
 import struct
@@ -7,6 +8,7 @@
 from cm_interface.device.mcu import (
     ADC_CHANNEL_COUNT,
     MCU,
+    RTC_SET_MIN_SECONDS,
     AdcReg,
     AlarmReg,
     AlarmTaskState,
@@ -28,6 +30,7 @@
     SystemReg,
     TemperatureAlarmBit,
     describe_reset_cause,
+    rtc_local_seconds,
 )
 from cm_interface.errors import (
     CMError,
@@ -50,7 +53,7 @@ def __init__(self):
                     | McuCapability.ALARMS | McuCapability.ADC
                     | McuCapability.PERSISTENT_LOG | McuCapability.CONTROLS
                     | McuCapability.RUNTIME | McuCapability.CONFIG
-                    | McuCapability.CONFIG_WRITE)
+                    | McuCapability.CONFIG_WRITE | McuCapability.RTC_WRITE)
         self.put(McuPage.SYSTEM, SystemReg.CAPABILITIES,
                  int(all_caps).to_bytes(4, "little"))
 
@@ -483,6 +486,56 @@ def test_centipercent_roundtrip_all_wire_percents(self):
             self.assertEqual(int(round((cpct / 100.0) * 100)), cpct)
 
 
+class McuRtcWriteTest(unittest.TestCase):
+    def _rtc_write(self, seconds):
+        return (int(McuPage.CONTROL), int(ControlReg.RTC_SET_LOCAL),
+                seconds.to_bytes(4, "little"))
+
+    def test_set_rtc_writes_local_seconds(self):
+        # expected values hand-computed from day counts, not via calendar.timegm
+        cases = (
+            (datetime.datetime(2026, 1, 1, 0, 0, 0), 1767225600),
+            (datetime.datetime(2028, 2, 29, 0, 0, 0), 1835395200),
+            (datetime.datetime(2026, 12, 31, 23, 59, 59), 1798761599),
+        )
+        for when, expected in cases:
+            mcu = MemoryMCU()
+            self.assertEqual(mcu.set_rtc(when), expected)
+            self.assertEqual(mcu.writes, [self._rtc_write(expected)])
+
+    def test_set_rtc_drops_microseconds(self):
+        mcu = MemoryMCU()
+        mcu.set_rtc(datetime.datetime(2026, 1, 1, 0, 0, 0, 999999))
+        self.assertEqual(mcu.writes, [self._rtc_write(1767225600)])
+
+    def test_set_rtc_bound_matches_constant(self):
+        self.assertEqual(
+            rtc_local_seconds(datetime.datetime(2026, 1, 1)), RTC_SET_MIN_SECONDS)
+
+    def test_set_rtc_rejects_before_2026(self):
+        for bad in (datetime.datetime(2025, 12, 31, 23, 59, 59),
+                    datetime.datetime(1970, 1, 1),
+                    datetime.datetime(2106, 2, 8)):
+            mcu = MemoryMCU()
+            with self.assertRaises(ValueError):
+                mcu.set_rtc(bad)
+            self.assertEqual(mcu.writes, [])
+
+    def test_aware_datetime_converts_to_host_local(self):
+        aware = datetime.datetime(2026, 6, 1, 12, 0, 0, tzinfo=datetime.timezone.utc)
+        local = datetime.datetime.fromtimestamp(aware.timestamp())
+        self.assertEqual(rtc_local_seconds(aware), rtc_local_seconds(local))
+
+    def test_set_rtc_gated_by_separate_capability(self):
+        mcu = MemoryMCU()
+        _put_u32(mcu, McuPage.SYSTEM, SystemReg.CAPABILITIES,
+                 McuCapability.SYSTEM | McuCapability.CONTROLS)
+        mcu.send_control(McuControlCommand.CLEAR_POWER_FAULT)  # commands still work
+        with self.assertRaises(McuCapabilityUnavailable):
+            mcu.set_rtc(datetime.datetime(2026, 6, 1))
+        self.assertEqual(len(mcu.writes), 1)
+
+
 class McuCapabilityGatingTest(unittest.TestCase):
     def _system_only(self):
         mcu = MemoryMCU()

tests/test_wire_contract.py

@@ -194,6 +194,10 @@ def test_config_write_clamps(defines):
     assert _resolve("CFG_VOLT_MAX_CPCT", defines) == mcu.ALARM_VOLT_CPCT_MAX
 
 
+def test_rtc_set_lower_bound(defines):
+    assert _resolve("RTC_SET_MIN_SECONDS", defines) == mcu.RTC_SET_MIN_SECONDS
+
+
 def test_runtime_page(defines):
     _check(defines, [
         ("RT_OFF_HEAP_FREE", mcu.RuntimeReg.HEAP_FREE),
@@ -250,6 +254,7 @@ def test_adc_and_control_pages(defines):
     _check(defines, [
         ("ADC_PAGE_VALUES_OFF", mcu.AdcReg.VALUES),
         ("CTRL_OFF_COMMAND", mcu.ControlReg.COMMAND),
+        ("CTRL_OFF_RTC_SET_LOCAL", mcu.ControlReg.RTC_SET_LOCAL),
         ("CTRL_CMD_ASSERT_PROGCOM_POWER_INHIBIT",
          mcu.McuControlCommand.ASSERT_PROGCOM_POWER_INHIBIT),
         ("CTRL_CMD_RELEASE_PROGCOM_POWER_INHIBIT",
@@ -274,6 +279,7 @@ def test_capability_and_health_bits(defines):
         ("MCU_CAP_CONFIG", mcu.McuCapability.CONFIG),
         ("MCU_CAP_RUNTIME", mcu.McuCapability.RUNTIME),
         ("MCU_CAP_CONFIG_WRITE", mcu.McuCapability.CONFIG_WRITE),
+        ("MCU_CAP_RTC_WRITE", mcu.McuCapability.RTC_WRITE),
         ("MCU_HEALTH_POWER_FAULT", mcu.McuHealth.POWER_FAULT),
         ("MCU_HEALTH_TEMPERATURE_ALARM", mcu.McuHealth.TEMPERATURE_ALARM),
         ("MCU_HEALTH_VOLTAGE_ALARM", mcu.McuHealth.VOLTAGE_ALARM),