Added setup 77 - GC9A01 in Parallel with STM32

User_Setups/Setup77_STM32_GC9A01_Parallel.h

@@ -0,0 +1,120 @@
+//                            USER DEFINED SETTINGS
+//   Set driver type, fonts to be loaded, pins used and SPI control method etc.
+//
+//   See the User_Setup_Select.h file if you wish to be able to define multiple
+//   setups and then easily select which setup file is used by the compiler.
+//
+//   If this file is edited correctly then all the library example sketches should
+//   run without the need to make any more changes for a particular hardware setup!
+//   Note that some sketches are designed for a particular TFT pixel width/height
+
+#define USER_SETUP_ID 0x77
+
+// Define to disable all #warnings in library (can be put in User_Setup_Select.h)
+//#define DISABLE_ALL_LIBRARY_WARNINGS
+
+// ##################################################################################
+//
+// Section 1. Call up the right driver file and any options for it
+//
+// ##################################################################################
+
+// Define STM32 to invoke optimised processor support (only for STM32)
+#define STM32
+
+
+// STM32 8-bit parallel only:
+// If STN32 Port A or B pins 0-7 are used for 8-bit parallel data bus bits 0-7
+// then this will improve rendering performance by a factor of ~8x
+#define STM_PORTA_DATA_BUS
+//#define STM_PORTB_DATA_BUS
+
+// Tell the library to use 8-bit parallel mode (otherwise SPI is assumed)
+#define TFT_PARALLEL_8_BIT
+
+
+#define GC9A01_DRIVER
+
+
+ #define TFT_HEIGHT 240 // GC9A01 240 x 240
+
+
+// If colours are inverted (white shows as black) then uncomment one of the next
+// 2 lines try both options, one of the options should correct the inversion.
+
+// #define TFT_INVERSION_ON
+#define TFT_INVERSION_OFF
+
+
+// ##################################################################################
+//
+// Section 2. Define the pins that are used to interface with the display here
+//
+// ##################################################################################
+
+
+
+// ######       EDIT THE PINs BELOW TO SUIT YOUR STM32 PARALLEL TFT SETUP        ######
+
+
+// Tell the library to use 8-bit parallel mode (otherwise SPI is assumed)
+#define TFT_PARALLEL_8_BIT
+
+// The STM32 and TFT the pins used for testing are:
+#define TFT_CS  PC0   // Chip select control pin (library pulls permanently low
+#define TFT_DC  PC1   // Data Command control pin 
+#define TFT_RST PC2   // Reset pin, toggles on startup
+
+#define TFT_WR  PB2    // Write strobe control pin  
+#define TFT_RD  PB4    // Read strobe control pin
+
+#define TFT_D0  PA0   
+#define TFT_D1  PA1   
+#define TFT_D2  PA2   // Pins can be randomly assigned, this does not affect
+#define TFT_D3  PA3   // TFT screen update performance.
+#define TFT_D4  PA4 
+#define TFT_D5  PA5 
+#define TFT_D6  PA6 
+#define TFT_D7  PA7 
+
+
+// ##################################################################################
+//
+// Section 3. Define the fonts that are to be used here
+//
+// ##################################################################################
+
+
+#define LOAD_GLCD   // Font 1. Original Adafruit 8 pixel font needs ~1820 bytes in FLASH
+#define LOAD_FONT2  // Font 2. Small 16 pixel high font, needs ~3534 bytes in FLASH, 96 characters
+#define LOAD_FONT4  // Font 4. Medium 26 pixel high font, needs ~5848 bytes in FLASH, 96 characters
+#define LOAD_FONT6  // Font 6. Large 48 pixel font, needs ~2666 bytes in FLASH, only characters 1234567890:-.apm
+#define LOAD_FONT7  // Font 7. 7 segment 48 pixel font, needs ~2438 bytes in FLASH, only characters 1234567890:-.
+#define LOAD_FONT8  // Font 8. Large 75 pixel font needs ~3256 bytes in FLASH, only characters 1234567890:-.
+//#define LOAD_FONT8N // Font 8. Alternative to Font 8 above, slightly narrower, so 3 digits fit a 160 pixel TFT
+#define LOAD_GFXFF  // FreeFonts. Include access to the 48 Adafruit_GFX free fonts FF1 to FF48 and custom fonts
+
+// Comment out the #define below to stop the SPIFFS filing system and smooth font code being loaded
+// this will save ~20kbytes of FLASH
+#define SMOOTH_FONT
+
+
+// ##################################################################################
+//
+// Section 4. Other options
+//
+// ##################################################################################
+
+
+
+
+
+
+// Comment out the following #define if "SPI Transactions" do not need to be
+// supported. When commented out the code size will be smaller and sketches will
+// run slightly faster, so leave it commented out unless you need it!
+
+// Transaction support is needed to work with SD library but not needed with TFT_SdFat
+// Transaction support is required if other SPI devices are connected.
+
+// #define SUPPORT_TRANSACTIONS