ImportError: No module named gaugette.ssd1306

[xelamod]

Hello,
I'm a beginner with all of this and installed everything cording to the instructions but i'm getting the following error:
Traceback (most recent call last):
File "bartender.py", line 1, in
import gaugette.ssd1306
ImportError: No module named gaugette.ssd1306

what did I missed?
thanks!

[ddejesu]

I am having the same issue. if you could please direct us towards a solution it would be great. thanks

[joe2824]

Read the README file onece again and execute the setup OLED...

https://github.com/HackerShackOfficial/Smart-Bartender/blob/master/README.md#oled-setup

[dexterch]

I did everything as well but same issue

[jbiams77]

I am also having the same issue

[festermax]

hi to all!

first of all i hope everybody can apologize me for my englis, second i hope samebody can halp me.

i've make, mounted ed connected all bartender hardware, box, raspberry pi zero HW, trasf, DC-DC regulator, relays, tubes, pirostatic pump, diode and tubes, display and button... all ok, switched on and nothing was explosed!!!! so i think good :-).

for OLED dispaly, i've used :
https://www.amazon.it/DollaTek-Pollici-Display-SSD1306-Schermo/dp/B07QJ39RDJ/ref=sr_1_fkmr0_1?__mk_it_IT=%C3%85M%C3%85%C5%BD%C3%95%C3%91&keywords=dollatek+0.96+oled+ssd1306+spi&qid=1575331486&sr=8-1-fkmr0

and used this connections:
GND --> Ground (PIN 6)
VCC --> 3V3 (PIN 1)
D0 --> SPI0_SCLK (PIN 23)
D1 --> SPI0_MOSI (PIN 19)
RST --> GPIO14 (PIN 8)
DC --> GPIO15 (PIN 10)

so all the hardware explaned.

software, (bigggg problems... for me...)
rasbian buster lite (no desktop) on raspberry pi zero HW.
tryed the guide:
https://github.com/HackerShackOfficial/Smart-Bartender
bat nothing of the instructions was executed correcty...

First configuration in raspi-config for I2C, SPI and GPIO, WIFI and SSH for shell remote controll.

python -V : Python 2.7.16

"sudo apt install python-pip" :
(answer: just installed most new version (18.1-5+rpt1))

"sudo pip install unicornhat" :
Looking in indexes: https://pypi.org/simple, https://www.piwheels.org/simple
Requirement already satisfied: unicornhat in /usr/local/lib/python2.7/dist-packa ges (2.2.3)
Requirement already satisfied: rpi-ws281x>=3.0.3 in /usr/local/lib/python2.7/dis t-packages (from unicornhat) (4.2.2)

"Enable SPI" :
maked

"I2C" :
maked

"OLED Setup" :

git clone https://github.com/HackerShackOfficial/Smart-Bartender
git clone https://github.com/the-raspberry-pi-guy/oled :
Folders created.
all two folders in Home/pi/

"sh OLEDinstall.sh"
python-pil ????
"python-imaging" no candidates to install. ????
so i'll went to: https://learn.adafruit.com/adafruit-oled-displays-for-raspberry-pi/setting-up

"sudo apt-get install git-core"
Note, selected "git" in place of "git-core"
git just most recent version (1:2.20.1-2).

"sudo nano /etc/modprobe.d/raspi-blacklist.conf"
ok, only text edited.

"sudo nano /etc/modules"
ok.

"sudo reboot"

"git clone https://github.com/the-raspberry-pi-guy/OLED"
Done!

"cd OLED"
Ok.

"sh OLEDinstall.sh"
E: Pack "python-imaging" no candidates to install.

Running the Code:

"sudo pip install -r requirements.txt"
Looking in indexes: https://pypi.org/simple, https://www.piwheels.org/simple
Requirement already satisfied: RPi.GPIO==0.6.3 in /usr/local/lib/python2.7/dist-packages (from -r
requirements.txt (line 1)) (0.6.3)

"sudo python bartender.py"
Traceback (most recent call last):
File "bartender.py", line 1, in
import gaugette.ssd1306
ImportError: No module named gaugette.ssd1306

so.. i went on internet about this error : https://forums.adafruit.com/viewtopic.php?f=47&t=76458

and i've used this code:
"sudo python setup.py install"
python: can't open file 'setup.py': [Errno 2] No such file or directory

"sudo apt-get update"
Done.

"sudo apt-get install build-essential python-dev python-pip"
build-essential just most recent version (12.6).
python-dev just most recent version (2.7.16-1).
python-pip just most recent version (18.1-5+rpt1).
0 updated, 0 installed, 0 to remove e 57 not updated.

"sudo pip install spidev"
Looking in indexes: https://pypi.org/simple, https://www.piwheels.org/simple
Requirement already satisfied: spidev in /usr/local/lib/python2.7/dist-packages (3.4)

i don't know what i need to do more... this project it was like very simple, bat i'm too stupid...
please help me....

Demetrio.

[RobbieBakker]

Hi! I'm having the same issue on the gaugette.ssd1306 module which cannot be found. Any solutions yet?

[willchickering]

Exact same issue. I cannot rabbit hole deep enough to find out why 'ImportError: No module named gaugette.ssd1306' keeps popping up. HELP!!!

[rinks1020]

did anyone get the solution for "no module named gaugette.ssd1306"

[kevinvugts]

did anyone get the solution for "no module named gaugette.ssd1306"

Nope, and it’s a shame that the owners of this project are not responding at all, despite the fact we pay them a monthly fee on patreon to support more of these projects…..

[derelvis]

Did anyone try to download the gaugette folder from here https://github.com/guyc/py-gaugette/tree/master/gaugette and just put it into the bartender folder? Did not try it as I used another lib for my display. But might work.

[kevinvugts]

@rinks1020 @derelvis @willchickering @RobbieBakker @festermax @ddejesu @dexterch @jbiams77 @xelamod @joe2824 Hi guys, is there anyone who is still struggling with this issue? I made a complete rewrite from what HackerShack initially wrote back in 2017. I am using the newest libraries right now with support from raspberry pi 3 to the newest version 4.

Let me know in a reply if you're interested in this.

Best Regards,
Kevin.

[derelvis]

Hi Kevin,
sure, please give it a go! Mine is up and running but it is always interesting to see who others managed to get it working. I extended mine by another 8 buttons to fire drinks by just one button press (8 pumps) and did some other tweaks as well. Did think about creating a fork already but never used git before. ;-)
Best Daniel

[C-l-a-r-k-y]

Kevinvugts. I am having all sorts of issues getting the OLED to work. If you have new code with up to date libraries, would you be willing to share them please

[kevinvugts]

Kevinvugts. I am having all sorts of issues getting the OLED to work. If you have new code with up to date libraries, would you be willing to share them please

I got ya. I will upload my code changes to github next week. Will stay in touch.

[C-l-a-r-k-y]

Kevinvugts. I am having all sorts of issues getting the OLED to work. If you have new code with up to date libraries, would you be willing to share them please

I got ya. I will upload my code changes to github next week. Will stay in touch.

Thanks Kevin,
Do you know when your code will be available?
Happy to contribute for a fix, issue has had me scratching my head for hours.